What're your thoughts and feelings on How to Install a Bathtub?
Setting up a bathtub isn't specifically rocket science, however it does need solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a new one is also a reasonably challenging project. If the old bathtub is easily accessible, the job can move speedily; if you need to open a wall surface to eliminate the old bathtub and also place the new tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to leave the old tub as well as set in the brand-new one. Make sure you have actually qualified yourself for the task as well as fit trying it. As opposed to hiring a contractor to take over a halfway-completed project, it is far better to consider using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This short article will certainly aid you install a brand-new tub in your bathroom if you have currently bought a brand-new tub and also do not require to change the setup of your previous water system pipelines.
Your tools as well as product checklist ought to comprise the following:
Planning for the Setup
First of all, the supporting structure provided with the bathroom should be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of removing the existing taps can be rather bothersome as a result of the limited access that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipes. When the supply pipes have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Before going on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, position the bath tub in the needed position. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To install taps, fit the bottom of the furthest versatile tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water as well as inspect all joints and new pipework for leakages and tighten them if required. Fill up the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the tub needs to wait until the tub has actually been made use of at the very least when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the tap and the sink. Secure the tap in place with the maker provided backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind must be linked to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, causing issues with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the market. It is a good idea to fit the ceramic tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you appreciated the entire article. Make sure you take the time to share this blog if you enjoyed it. Many thanks for your time spent reading it.
Hot water gone? Call.